# Steps To How To Tie A Tie

Posted on

If you are looking for the answer of steps to how to tie a tie, you’ve got the right page. We have approximately 10 FAQ regarding steps to how to tie a tie. Read it below.

## Maureen spent \$25.60 for a shirt and tie. The shirt

Ask: Maureen spent \$25.60 for a shirt and tie. The shirt cost \$12 more than the tie. How much did the tie cost?

x = tie
x + 12 = shirt

x + x + 12 = 25.60

2x + 12 = 25.60

2x = 25.60 – 12

2x = 13.6

2x/2 = 13.6/2

x = 6.8

The tie costs \$6.8

x + 12

6.8 + 12 = 18.8

The shirt costs \$18.8

\$6.8 + \$18.8 = \$25.60

## how was tie dye invented?

Ask: how was tie dye invented?

## how was tie dye invented?

• Who invented tie dye is uncertain, but India, Japan and Africa are most prominent in written tie dye histories.
• Bandhani is the oldest known tie dye tradition still practiced.

• These Designs are made by plucking and tying many small points with thread before dyeing. It’s also known as Bandhni, Bandhej, and Plangi.

I hope this helps u comrade ☭☆❤️- Soviet kitty =^. ｡.^= ᵐᵉᵒʷˎˊ˗❄️

[tex]hugemathbb{underbrace{overbrace{ : : : ANSWER: : : : }}}[/tex]

[tex]hugemathbb{H}[/tex]ow was tie dye invented?

• Invented tie-dye from China and Japan. The process was used during the T’ang Dynasty in China and during the Nara Period in Japan until the 6th century.

#KeepOnLearning

## How to not tie a tie using tye?

Ask: How to not tie a tie using tye?

The simple oreint knot

1.Drape the tie around your collar with the seam facing inward and the thick end on your left, two or three inches lower than your desired finishing position.

2.Bring the thick end horizontally across the front of the narrow end, and then pass it back horizontally behind the narrow end.

3.Pass the thick end again across the front of the knot from left to right.

4.Now pass the thick end again behind the knot horizontally from right to left.

5.Pass the thick end AGAIN across the front of the knot from left to right. Slip a finger under this third horizontal loop.

6.Bring the tip of the thick end up underneath the loop around your collar and feed it up behind the knot, down over the front of the knot and through that third horizontal loop.

7.Pull the thick end through the horizontal loop and snug it down.

8.Adjust the tie by holding the knot in one hand and pulling gently on the narrow end with the other.

## if it takes ⅚ cm of rope to tie a

Ask: if it takes ⅚ cm of rope to tie a fence, then how many cm will it take to tie 4 fences? ​

10/3 cm of rope

Step-by-step explanation:

asdfghjkl

## What is the Steps in splicing western union long-tie joint​

Ask: What is the Steps in splicing western union long-tie joint​

How do you make a Western Union splice?

The Western Union Splice is made by twisting two ends of a wire together counterclockwise 3/4 of a turn each, finger tight. Then, using needle-nose pliers, the ends are twisted at least five more turns, tightly. The cut off ends are pushed close to the center wire.

Explanation:

I hope I can help with your modules, give me 5 stars and heart or ELSE!

## How to secure the loops of Dior Bow Tie Ribbon?A.

Ask: How to secure the loops of Dior Bow Tie Ribbon?

A. tie a double knot on the backside of the bow

B. tie the bow directly to another ribbon on your package

C. tie a double knot around the midpoint with a thin piece of ribbon

D. tie a knot around the midpoint with a thin piece of ribbon and floral wire

C:tie a double knot around the mindpoint with a thin piece of ribbon

Explanation:

i hope it’s help

## steps in making western union long tie in computer

Ask: steps in making western union long tie in computer

Figure parts A-D show steps in forming a “short tie” Western Union splice. Figure parts E and F show two possible “long tie” variations.

## What is the main step of tie-dyeing?

Ask: What is the main step of tie-dyeing?

fold or crumple fabric and tie it with string or rubber bands.

## How to Tie a tie Task 17

Drape the necktie around your collar with the thick end on the left. This end should be hanging a good four to six inches lower than the finished length you desire.

Cross the thick end horizontally in front of the thin end from left to right.

Bring the thick end around behind the thin end horizontally from right to left.

Flip the thick end up in front of the loop around your collar.

Tuck the thick end down behind the loop around your collar, emerging on the right side of the thin end.

Bring the thick end in front across the earlier horizontal band and the diagonal you created in Step 5. Slip a finger under this new horizontal crossing.

Bring the thick end around behind the knot from left to right.

Bring the thick end across the front, right on top of the horizontal fold you made in Step 6. (Your finger should still be holding the fold open.) Keep both horizontal bands held slightly off the collar with a finger.

Bring the thick end up underneath the loop around your collar.

Tuck the thick end down behind both of the horizontal crossings and pull through.

Pull the knot into place by holding the knot with one hand. Now tug gently on the thin end with the other. Use your finger to tease out the diagonal folds until the X shape of the knot is very clear.

## explain the steps for 2 different types of tie dye

Ask: explain the steps for 2 different types of tie dye designs​